previous
  • Electrical Articles & Videos
    Electrical Articles & Videos
  • Video: Build a curved step
    Video: Build a curved step
  • Buyer's Guide to Insulation
    Buyer's Guide to Insulation
  • All about Roofing
    All about Roofing
  • 9 Concrete Countertops Ideas
    9 Concrete Countertops Ideas
  • Remodeling in Action
    Remodeling in Action
  • Read FHB on Your iPad
    Read FHB on Your iPad
  • 7 Trim Carpentry Secrets
    7 Trim Carpentry Secrets
  • The Hobbit House and More
    The Hobbit House and More
  • How to Install Housewrap Solo
    How to Install Housewrap Solo
  • Shorten a Prehung Door
    Shorten a Prehung Door
  • Energy-Smart Details
    Energy-Smart Details
  • Tips & Techniques for Painting
    Tips & Techniques for Painting
  • 7 Small Bathroom Layouts
    7 Small Bathroom Layouts
  • Deck Design & Construction
    Deck Design & Construction
  • 12 Remodeling Secrets
    12 Remodeling Secrets
  • Magazine Departments
    Magazine Departments
  • Play the Inspector Game!
    Play the Inspector Game!
  • Basement Remodeling Tips
    Basement Remodeling Tips
  • Master Carpenter Videos
    Master Carpenter Videos
  • The Passive House Build
    The Passive House Build
  • Clever daily tip in your inbox
    Clever daily tip in your inbox
  • 7 Smart Kitchen Solutions
    7 Smart Kitchen Solutions
next
Pin It

Bay-Window Roof: How to Frame the Base

HVT417-bay-window-roof-base.jpg

To build the roof, I begin by making a template for the base. To lay out the framing, I only need two measurements from this bay window. One is the overall width: 62¼. The other measurement I need is the overall depth. But I have to realize this window is going inside the rough opening 4 inches. So I draw a line all the way across, 4 inches out—and now I measure from the outside of the window to that line, 17 7/8 inch; that’s my overall depth. I want to copy the shape of the head board onto a piece of ¾-inch OSB. This will be my guide for framing. First, I draw a rectangle centered on the sheet, using my 62¼ by 17 7/8 measurements. Then, to get the 45-degree angles, I measure in 17 7/8 inch from each end and draw the lines. Now I have an exact replica of the bay window top. But before I begin the roof framing, I have to add a roof overhang using a strap of soffit material. What I want to do is extend that out because I’m going to have a soffit overhang of 4½ inches. Line the soffit material up with the outside edges—just extend those lines right out, which represents the outside edge of the framing—all the way around.

Now that I have outside edges, I measure from point to point to get my first set of cuts. The right is 31 7/8, and the center 30 inches. And the left is the same as the other side; 31 7/8. And this piece will have a 22½-degree angle here, and a 45 on the other end. This piece will have a 22½-degree angle on both ends, and this piece will have a 22½ here and a 45 there.

I’m going to lay them out, right along the lines, and outline the outside of the frame. Then I measure the inside—71—so I’ll cut that, put it in, and then I’ll have the base framed up. All right; that fits well. Next, I’ll cut these miniature joists to fit in here. Then all I have to do is fasten everything together. I have to put blocking in so that when I put the trim on from underneath, it’ll have someplace to catch on the outside edges.




Become a Fine Homebuilding Member

to view this video

Learn More